Authorized AMSOIL Dealer
JONATHAN L LACKMAN
Castle Pines, CO
Independent AMSOIL Dealer · Jonathan Lackman · Denver, CO Ships nationwide from AMSOIL · Not the official AMSOIL site

AMSOIL Z-ROD oil for classic and flat-tappet engines

I earn a commission when you buy or join through my links · Disclosure

Quick answer

For a classic or muscle-car engine with a flat-tappet cam, AMSOIL’s product is Z-ROD 100% Synthetic Motor Oil, in 10W-30, 10W-40 and 20W-50. It is formulated with high zinc and high phosphorus (ZDDP) for cam and lifter protection, plus rust inhibitors for engines that sit. AMSOIL’s maximum drain is 5,000 miles or two years, whichever comes first. The owner sets a shorter interval when the engine is modified. Z-ROD is intended for engines that specify 10W-30, 10W-40 or 20W-50 and API SL or earlier, not as a high-zinc dump into a modern catalytic-converter engine that requires API SM or newer.

Modern gasoline oils are built around tight emissions hardware. A 1960s small-block with a flat-tappet cam is built around a different wear problem. Those two jobs are not the same oil.

What Z-ROD is for

AMSOIL’s Z-ROD bulletin (G2883, February 2021) describes a high-zinc, high-phosphorus synthetic for engines that need 10W-30, 10W-40 or 20W-50 and API SL or earlier. The ZDDP level is high enough that AMSOIL says it exceeds API SM and newer limits. That’s by design for a flat-tappet cam, and it’s why I don’t put Z-ROD in a late-model catalyst-equipped engine that requires a current API service category.

I am not going to quote zinc or phosphorus parts-per-million figures that aren’t on the official typical-properties table of that bulletin.

Grades:

  • 10W-30 (stock code ZRT)
  • 10W-40 (ZRD)
  • 20W-50 (ZRF)

Drain interval and mixing

AMSOIL’s maximum drain is 5,000 miles or two years, whichever comes first. You own the interval if the cam is wild, the engine sees track heat, or it sits for months. Change the filter with the oil.

Z-ROD is compatible with other conventional and synthetic motor oils, but AMSOIL says mixing shortens the oil’s life, and it tells you not to use aftermarket additives. If you’re switching, do a complete oil and filter change. See Can you mix AMSOIL?.

Rust when the car sits

Storage is half the job on a car that doesn’t get weekly miles. In AMSOIL’s ASTM D1748-10 humidity-cabinet test of Z-ROD 10W-40, AMSOIL reports the Z-ROD coupon showed no rust, while a leading competitor’s coupon (oil obtained July 25, 2019, in that in-house test) rusted. That’s a storage-protection result, not a cam-wear dyno.

My brother Jesse runs RevSearch, an engine dyno shop in North Dakota that works on engine development and publishes notes on engine oils and flat-tappet cams.

AMSOIL Z-ROD 10W-30 100% Synthetic Motor Oil (ZRT)

Best for: Flat-tappet and classic engines that call for 10W-30 and API SL or earlier, including cars that sit between drives.

  • High-zinc, high-phosphorus formula for flat-tappet cams (G2883)
  • Rust inhibitors; no rust on the Z-ROD coupon in AMSOIL’s ASTM D1748-10 cabinet test of the 10W-40
  • Maximum drain 5,000 miles or two years, whichever comes first

Tip: Preferred Customers get member pricing. Join at AMSOIL.com

Other viscosities: Z-ROD 10W-40 · Z-ROD 20W-50

If the engine is a late-model GDI or EcoBoost that specifies a current gasoline oil, go back to Signature Series and leave the ZDDP oil in the classic.

I’m an Independent AMSOIL Dealer, not an AMSOIL INC. employee.

Frequently asked questions

Do I need a high-zinc oil in a flat-tappet engine?
Flat-tappet cams rely on a strong anti-wear film at the cam lobe and lifter face. Modern passenger-car oils lowered zinc and phosphorus (ZDDP) to protect catalytic converters, starting with API SM. AMSOIL designed Z-ROD for older engines that still need that higher ZDDP level, and says the ZDDP content exceeds API SM and newer limits, which is why it is not the oil I recommend for a late-model catalyst-equipped daily driver.
Which Z-ROD grade should I use?
Match the viscosity the engine was set up for: 10W-30 (ZRT), 10W-40 (ZRD) or 20W-50 (ZRF). If the engine is modified, use the viscosity your builder specified, not a guess from the model year.
How often do I change Z-ROD?
AMSOIL’s maximum is 5,000 miles or two years, whichever comes first. You choose a shorter interval when the cam is aggressive, the engine idles at the track, or it sits for long stretches. This is not a Signature Series 25,000-mile oil.
Can I add a zinc aftermarket additive to regular AMSOIL?
AMSOIL says not to use aftermarket additives with Z-ROD, and mixing other oils shortens the oil’s effective life even though the chemistries are compatible. Use Z-ROD as the oil, not as a booster in a modern gasoline oil.
Will Z-ROD protect an engine that sits all winter?
AMSOIL formulates Z-ROD with rust inhibitors and reports that in ASTM D1748-10 humidity-cabinet testing, a Z-ROD 10W-40 coupon showed no rust, while a leading competitor’s coupon rusted. That competitor oil was obtained on July 25, 2019, in AMSOIL’s in-house test. I won’t name a brand AMSOIL did not name.

Sources

Product facts on this page come from AMSOIL’s official product pages and literature. Always follow your owner’s manual.

  1. AMSOIL Z-ROD data bulletin (G2883, 2/21)
  2. AMSOIL Z-ROD 10W-30 100% Synthetic Motor Oil (ZRT)